Land Rover 300Tdi timing belt, Dayco 94566, part ERR1092

The 300Tdi cambelt is not a job to put off. It drives the camshaft and the injection pump, and if it lets go while the engine is running you are usually looking at bent valves and a cylinder head off. Plenty of good engines have been scrapped for the sake of a belt somebody kept meaning to change.

It is also not a job to improvise. Land Rover's procedure depends on locking tools and a dial torque wrench to set belt tension, and the timing is set by pinning the injection pump rather than by eye. This guide follows the factory overhaul manual, and every torque figure below is quoted from it. Where the manual gives no figure, we say so rather than filling the gap in.

How to tell it needs changing

  • You cannot prove when it was last done. No receipt, no date chalked on the cover, nothing in the book. This is the most common reason a 300Tdi belt fails, and it is reason enough on its own.
  • On schedule, not on condition. A cambelt can look perfect and still be near the end of its life. Age counts as much as mileage, and a vehicle that has stood for years has an old belt whatever the odometer says.
  • Cracks, glazing or a hard, shiny face. Take the front cover off and look at it properly. A belt that has gone hard or crazed is finished.
  • Any sign of oil or coolant contamination. A leaking crankshaft front seal, cam seal or water pump will soften a belt quickly. Fix the leak while the covers are off or you will be doing this again.
  • Squealing or rumbling from the front of the engine. Often the tensioner or idler bearing rather than the belt. Spin both by hand with the belt off: any grittiness or side play and the bearing is going.
  • Tensioner at the end of its travel. A belt stretched to the limit of adjustment has had enough.
  • Whenever the front cover is off for other work. The belt, tensioner and idler are cheap next to a cylinder head rebuild.

Be careful with the intervals quoted online. They vary a great deal and we could not confirm an official Land Rover figure for the 300Tdi from a primary source, so use the schedule in your own handbook for your vehicle and model year. When in doubt, do it early.

Tools you will actually need

This is the honest part. Without these you cannot do the job to the factory procedure:

  • LRT-12-044 - flywheel or drive plate locking tool
  • LRT-12-045 - injection pump timing pin
  • LRT-12-080 - crankshaft pulley restraint
  • LRT-12-031 and LRT-12-049 - crankshaft pulley removal
  • LRT-12-078 - crankshaft gear removal
  • LRT-12-077 - crankshaft front seal replacer
  • A dial-type torque wrench reading 0-20 Nm - belt tension is set as a torque reading, not by thumb pressure, so a click wrench set to a high range will not do it. This is the tool people skip, and skipping it is why belts come back slack.
  • New belt, tensioner, idler, crankshaft front oil seal, front cover gasket and crankshaft O-ring. The manual tells you to discard the seal, gasket and O-ring, and it is right.

The locking tool and the timing pin are the two you genuinely cannot work around; aftermarket 300Tdi timing kits include both. A good puller and a careful hand will cover most of the rest.

One thing to be clear about before you start: the procedure below comes from the engine overhaul manual, which is written with the engine on a stand. Doing it in the vehicle means getting the front end out of the way first - grille panel, radiator and intercooler, viscous fan and the auxiliary belt. That varies by model year and by what has been fitted since, so work from the vehicle sections of the manual for that part. Disconnect the battery before you start, and once the belt is off do not turn the engine on the starter for any reason.

Removing the belt

  1. Fit LRT-12-080 to the crankshaft pulley with four bolts, restrain the crankshaft and remove the pulley flange head bolt. Early engines use a bolt and washer instead of a flange head bolt.
  2. Fit LRT-12-049 with the thrust button from LRT-12-031 and draw the pulley off. Recover the Woodruff key.
  3. Progressively slacken and remove the 14 timing belt front cover bolts in the sequence shown in the manual, then remove the cover, gasket and crankshaft front oil seal.
  4. Refit the crankshaft pulley bolt temporarily and rotate the crankshaft clockwise until LRT-12-044 locates in the flywheel slot. On manual gearboxes, remove the plug from the flywheel housing first. On automatics the tool passes through the engine plate into the drive plate slot.
  5. Check the camshaft pulley timing mark lines up with the mark on the rear cover, and that the Woodruff key lines up with the arrow on the rear cover. If either is out, stop and find out why before going further. Remove the pulley bolt.
  6. Insert timing pin LRT-12-045 through the injection pump gear hub plate into the pump hub.
  7. Slacken, but do not remove, the camshaft drive gear centre bolt.
  8. If you intend to refit the same belt, mark its direction of rotation on the outside face now.
  9. Slacken the tensioner pulley bolt and move the pulley to release the belt.
  10. Remove the idler pulley nut and washer, release the idler and remove it. Slip the belt off the gears and discard it.
  11. Remove the crankshaft gear with LRT-12-031 and LRT-12-078, recover the Woodruff key and discard the O-ring.
  12. Remove the tensioner pulley bolt and slotted washer, then the pulley and bracket. Recover the flanged spacer.
  13. Remove the camshaft gear centre bolt and washer, then withdraw the gear and hub plate as one assembly.
  14. Remove the three bolts holding the injection pump gear and hub plate to the pump hub, then remove LRT-12-045 and take off the gear and hub plate.

The four cautions that cost engines

These are printed in the manual as CAUTION notices, and they are there because people get them wrong:

  • Never rotate the crankshaft anti-clockwise.
  • Never turn the engine using the camshaft or injection pump gear bolts.
  • Do not remove the three bolts securing the hub plate to the gear during removal.
  • Do not remove the nut securing the hub to the injection pump. Disturb that and you have lost the pump timing.

Fitting the new belt

  1. Fit a new O-ring to the crankshaft, then the Woodruff key, then the crankshaft gear, tapping it home with a soft mallet.
  2. Fit the camshaft gear and hub plate with its centre bolt and washer, finger tight.
  3. Fit the injection pump gear and hub plate, aligning the cut-out with the timing pin hole. Fit the three bolts lightly and insert LRT-12-045, adjusting the gear until the pin goes in. Do not fit the bolts through the elongated slots in the hub plate, and make sure the gear does not move as they are tightened.
  4. Fit the flanged spacer, tensioner pulley and bracket, and the slotted washer with the slot vertical. Bolt finger tight.
  5. Refit the crankshaft pulley bolt, rotate the crankshaft to lock with LRT-12-044, and confirm the Woodruff key aligns with the arrow on the rear cover. Adjust the camshaft gear on its centre bolt if needed, then remove the pulley bolt.
  6. Fit the belt by hand with the slack on the idler side. If refitting the original, check the rotation mark faces the right way. Do not lever a new belt on - you will damage the cords and not see it. Fit the idler pulley and tighten the nut to 45 Nm.
  7. With both locking tools still fitted, set belt tension with a dial torque wrench in the hole in the tensioner bracket, held vertically: 12 Nm for a used belt, 15 Nm for a new belt. Holding that tension, tighten the tensioner bolt to 45 Nm.
  8. Check LRT-12-045 still moves freely in the pump hub. If it does not, slacken the three hub plate bolts, move the gear slightly and recheck. Once it moves freely, tighten the three bolts to 25 Nm.
  9. Remove both tools, rotate the crankshaft clockwise through two full turns, then refit LRT-12-044.
  10. Slacken the tensioner bolt, re-tension the belt as above, and tighten the tensioner bolt to 45 Nm again. A new belt settles on its first revolutions, so this second pass is what sets the real tension - it is not optional.
  11. Refit LRT-12-045. If it will not go in, slacken the pump gear bolts and rotate the pump shaft on its nut until the pin slides home, then tighten to 25 Nm.
  12. Tighten the camshaft gear centre bolt to 80 Nm. Remove the timing pin and locking tool. Refit the flywheel housing plug and tighten to 12 Nm.
  13. Fit a new dry gasket to the rear cover - no sealant - position the front cover and fit the bolts, checking you have the right length in each hole, then tighten to 25 Nm in the manual's sequence.
  14. Fit the new crankshaft front seal with LRT-12-077 from inside the front cover, lightly oiled.
  15. Lightly oil the crankshaft spigot, fit the Woodruff key and pulley, fit LRT-12-080 with its four bolts, then tighten the pulley bolt to 80 Nm plus a further 90 degrees. The angle is part of the specification, not a flourish - this is a torque-plus-angle bolt and it will not be right without it.

Where else this job goes wrong

Tensioning by feel. The quarter-turn twist test you would use on an alternator belt tells you nothing here. Too slack jumps teeth; too tight destroys the idler and tensioner bearings you have just paid for.

Reusing the seal, gasket or O-ring. Oil onto a new belt undoes the entire job for the sake of three cheap parts.

Forcing the timing pin. If it will not slide in, the gear is out of position. Slacken the bolts and move it as the procedure describes. Forcing the pin only bends the pin.

What this job does not touch

Done as written, your injection pump timing stays exactly where it was. The pump gear is located to the hub by the timing pin, and the nut holding the hub to the pump shaft is deliberately left alone - the manual gives no torque figure for it because it tells you not to remove it. If that nut has been off, or the pump has moved on its mountings, you are into pump timing proper, which needs dial gauge equipment and the pump timing procedure from the manual. That is a different job, and guessing at it will cost you a pump.

Two things to re-check before you start it

Turn the engine over by hand through two full clockwise revolutions and confirm the timing marks still line up and the pin still enters the pump. If anything has shifted, stop and find out why - do not crank it on the starter to see what happens.

Count your tools. A locking pin left in the flywheel housing does a lot of damage very quickly.

Parts for the job

We stock 300Tdi timing belts, tensioners, idlers, seals and full cambelt kits, shipped from Alexandria, Virginia. The numbers worth knowing are the belt (ERR1092), the tensioner pulley (LHP100860), the idler pulley (LHV100150) and the timing cover gaskets (ERR4120 and ERR4860). A full kit is usually the sensible buy - replacing the belt and leaving a tired tensioner in place is false economy. If you are unsure what your engine takes, send us your VIN and we will check it before you order. Worth doing on this job in particular: 200Tdi and 300Tdi timing parts look near identical in a photograph, are not interchangeable, and a search for "timing belt" will hand you both.

This guide is provided for general reference and follows the Land Rover 300 TDi Engine Overhaul Manual. Always consult the workshop manual for your specific vehicle, take any figure we could not confirm here from that manual rather than from this page, and work safely: support the vehicle properly, disconnect the battery first, and never crank the engine with the belt removed.